Tools
- Phillips screwdriver, steps 9, 10, 11, 12 and 14
- Hammer, steps 2 and 4
- Allen key 100049 (included), step 5
- Wrench 113453 (included), steps 3, 7 and 8
Parts (14)
| Part | Count | Size | Goes in | Note |
|---|---|---|---|---|
| Head panel, lower | 1 | 165 × 38 × 2.2 cm | step 5 | Same size as the footboard, but this one has large round holes near its top edge. |
| Footboard | 1 | 165 × 38 × 2.2 cm | step 5 | Same size as the lower head panel, but with no large round holes on its face. |
| Headboard | 1 | 165 × 62 × 2.2 cm | step 8 | The tallest panel, with a row of holes along one long edge for dowels and studs. |
| Side rail | 2 | 204.6 × 22 × 2.5 cm | step 5 | Long side rail. Both rails are the same; the large cam holes face into the bed. |
| Slat rail 114290 | 1 | 200 × 3 × 3 cm | step 9 | Steel angle with slotted holes. It is the mirror image of 114291. |
| Slat rail 114291 | 1 | 200 × 3 × 3 cm | step 9 | Steel angle with slotted holes. It is the mirror image of 114290. |
| Brace 117228 | 4 | 91.4 × 3 × 1 cm | step 11 | Telescopic steel brace. All four are the same. |
| Centre beam | 1 | 204 × 8 × 5 cm | step 13 | Two-part telescopic beam, the longest steel piece. It rests on the two brackets. |
| Slats, left half | 1 | 200 × 74.5 cm, 8 mm thick | step 15 | Rolled slats, usually sold separately. Both halves are the same. |
| Slats, right half | 1 | 200 × 74.5 cm, 8 mm thick | step 15 | Rolled slats, usually sold separately. Both halves are the same. |
Hardware (101 pieces)
| Part no. | Hardware | Count | Size | Used in |
|---|---|---|---|---|
| 101367 | Wooden dowel, long | ×5 | Ø 8 × 50 mm | step 6 |
| 101359 | Wooden dowel, short | ×12 | Ø 8 × 30 mm | step 4 |
| 110789 | Chipboard screw, pointed | ×20 | Ø 4 × 16 mm | steps 9 and 10 |
| 105163 | Machine screw, blunt | ×8 | Ø 6 × 12 mm | step 14 |
| 117327 | Small machine screw | ×12 | Ø 5 × 8 mm | steps 11 and 12 |
| 10096286 | Slat holder | ×8 | Ø 25 × 30 mm | step 14 |
| 114254 | Flange nut | ×4 | Ø 13 × 8 mm | step 8 |
| 123491 | Cam bolt, wood thread | ×8 | Ø 8 × 55 mm | step 3 |
| 114334 | Threaded stud | ×4 | Ø 8 × 70 mm | step 7 |
| 114670 | Cam lock, large | ×8 | Ø 25 × 12 mm | step 5 |
| 122998 | Plastic wedge | ×4 | Ø 20 × 15 mm | step 8 |
| 122628 | Floor glide with pins | ×6 | Ø 18 × 45 mm | step 2 |
| 116791 | Centre beam bracket | ×2 | 100 × 80 × 40 mm | step 10 |
Sizes are as drawn in the 3D: diameter × length for fasteners, in millimeters.
The 15 steps
-
Step 1: Check your parts
Lay everything on a rug or the flattened box. Check the panels, steel rails, braces and centre beam against the list, then sort the hardware into bowls.
Tip: Two dowels look alike. 101367 is the long one and 101359 the short one, so keep them in separate bowls.
-
Step 2: Tap the glides onto the head and foot panels
Lay the lower head panel and the footboard flat on the rug. Tap 3 glides (122628) into the holes on the bottom edge of each panel until they sit flat.
Tip: Work on the rug or the box. A hard floor chips the panel edges.
-
Step 3: Screw in the cam bolts
With both panels still flat, screw 4 cam bolts (123491) into the inner face of each panel, two at each end. Turn them with the slot in the wrench 113453.
Watch out: Stop when the collar sits on the surface. A cam bolt driven into the panel sits too deep for the cam lock to grab.
-
Step 4: Push dowels into the side rail ends
Lay both side rails flat with the large holes facing up. Push 3 short dowels (101359) into each end, 12 in all, and tap them home lightly.
Watch out: Use the short dowels 101359 here. The long ones, 101367, belong on top of the head panel later.
-
Step 5: Join the frame with cam locks
With a helper, stand the head panel and footboard up and push both side rails onto their dowels and cam bolts. Drop a cam lock (114670) into each large hole and turn it clockwise with the Allen key until the joint pulls tight.
Watch out: Before each cam lock goes in, turn it so its arrow points to the end of the rail, toward the bolt. A cam pointing the wrong way locks nothing.
-
Step 6: Fit the long dowels on the head panel
Push the 5 long dowels (101367) into the holes along the top edge of the lower head panel.
-
Step 7: Screw the studs into the headboard
Lay the tall headboard flat on a table. Screw the 4 threaded studs (114334) into the holes in its bottom edge, wood thread first, using the wrench 113453.
Watch out: Stop when the smooth shoulder reaches the edge. Screwed in deeper, the stud is too short to take its nut.
-
Step 8: Mount the headboard
With a helper, lower the headboard onto the head panel so the dowels and studs drop into their holes. From the bed side, push a wedge (122998) onto each stud through the round holes. Screw on a flange nut (114254) and tighten it with the wrench.
Watch out: Tighten all four nuts firmly. A loose nut lets the headboard rock and creak.
-
Step 9: Screw on the slat rails
Hold slat rail 114290 against the inside of one side rail and 114291 against the other, at the same height. Drive 8 pointed screws (110789) through the slotted holes into each side rail.
Watch out: Use the pointed screws 110789 here, not the blunt machine screws 105163.
Tip: The manual shows two rail heights to suit different mattresses. Whichever you pick, use the same holes on both sides.
-
Step 10: Fit the centre beam brackets
Screw a beam bracket (116791) to the middle of the head panel's inner face and another to the footboard, with 2 pointed screws (110789) each. Use the holes at the same height as your slat rails.
Watch out: Pointed screws 110789 again, not the blunt machine screws 105163.
-
Step 11: Fit the four braces
Slide each brace (117228) out to length. Fix one end under a tab of a beam bracket and the other end under a slat rail, with a small screw (117327) at each end. Two braces run from each bracket, one to each side.
Tip: The braces are telescopic. Pull the inner bar out until both end holes line up with their screw holes.
-
Step 12: Square the frame and lock the braces
Look down on the frame. Both side rails must run straight, not bowed in or out. Once they do, drive a small screw (117327) into the slot of each brace to lock its length.
Watch out: If a side rail bows, these screws lock it in that shape. Push or pull the rail straight before you screw.
Tip: For a quick check, measure both diagonals from corner to corner. Equal lengths mean the frame is square.
-
Step 13: Drop in the centre beam
Slide the two halves of the centre beam apart until it reaches from bracket to bracket. Lower it onto the brackets at the head and at the foot.
Watch out: Keep your fingers out of the joint as the halves slide, because it can pinch hard. Hold the beam by its ends.
-
Step 14: Fit the slat holders
If you use a slatted base with its own frame or a box spring, skip this step and the next. Otherwise set 8 slat holders (10096286) on the slat rails and centre beam near the head and foot. Screw each one from below with a blunt screw (105163).
Tip: Turn each holder so its open side faces the slat end it will hold, as the two close-ups in the manual show.
-
Step 15: Roll out the slats
Unroll each half of the slats from the head end to the foot end, one on each side of the centre beam. Tuck the end slats under the holders, 4 on each side.
Tip: Underbed storage boxes are sold separately and come with their own instructions.
