Tools

  • Hex key 100001 (in the bag), steps 2 and 15
  • Hammer, step 3
  • Phillips screwdriver, step 17
  • Flat screwdriver, steps 19 and 20
  • Pencil, step 18
  • Spirit level, step 18

Parts (11)

PartCountSizeGoes inNote
Long panel (left side)1139 × 39 × 4 cmstep 2Thick long panel, 139 cm, dowel holes on one face. The same as the other long panel; this is the one you start with.
Long panel (right side)1139 × 39 × 4 cmstep 14Thick long panel, 139 cm, the same as the first. It goes on near the end.
Short panel (bottom)177 × 39 × 4 cmstep 2Thick short panel, 77 cm, screw holes near both ends. Same as the top; the first one you use becomes the bottom.
Short panel (top)177 × 39 × 4 cmstep 15Thick short panel, 77 cm, the same as the bottom. It goes on last.
Shelf369 × 39 × 1.6 cmsteps 4, 7 and 10Thin 69 cm board with dowel holes in both ends and the middle. Longer than the dividers.
Short divider439 × 33.6 × 1.6 cmsteps 3, 6, 9 and 12Thin board, about 34 cm. Shorter than the shelves; four of them.

Hardware (44 pieces)

Part no.HardwareCountSizeUsed in
104321Connector screw 104321/104322×8Ø 7 × 65 mmsteps 2 and 15
101339Wooden dowel×22Ø 8 × 40 mmsteps 3, 4, 5, 7, 8, 10, 11 and 13
10002300Felt pad (use 4 of the 8)×4Ø 30 × 3 mmstep 16
115753Wall bracket×260 × 45 × 40 mmstep 17
100372Short screw×4Ø 4 × 14 mmstep 17
103693Keyhole wall plate×240 × 30 × 2 mmstep 20
115754Bracket cover×2Ø 50 × 55 mmstep 20

Sizes are as drawn in the 3D: diameter × length for fasteners, in millimeters.

The 20 steps

  1. Step 1: Check your parts

    4 min

    Lay everything on a rug or the flattened box. Count 2 long panels, 2 short panels, 3 shelves and 4 dividers, and tip the hardware into bowls so nothing rolls away.

    Tip: The long and short panels are thick; the shelves and dividers are thin. Keep them in four piles so you grab the right board.

  2. Step 2: Screw a long panel to a short panel

    3 min · Hex key 100001 (in the bag) · Connector screw 104321/104322 104321 ×2

    Lay one long panel and one short panel on their edges on a rug, as drawn. Push 2 connector screws through the holes near the end of the short panel into the end of the long panel and tighten them with hex key 100001.

    Watch out: Work on a rug or the box, not a bare floor; corners chip. Drive the screws through the countersunk holes on the outside face of the short panel.

    Tip: The unit is built lying on its back. In the 3D view it stands up: this short panel is the bottom, this long panel the left side.

  3. Step 3: Fit the first short divider

    2 min · Hammer · Wooden dowel 101339 ×2

    Tap 2 dowels into the holes in the middle of the short panel's inner face with the hammer. Slide one short divider onto them, parallel to the long panel, until it sits tight.

    Tip: Dividers are the thin boards about 34 cm long. The thin 69 cm boards are the shelves.

  4. Step 4: Add the first shelf

    2 min · Wooden dowel 101339 ×2

    Push 2 dowels into the first pair of holes on the inner face of the long panel. Slide a 69 cm shelf onto them so it rests against the free end of the divider.

    Watch out: Push each board fully home before the next one. A gap of a few millimetres here keeps the second long panel from fitting later.

  5. Step 5: Dowels for the second divider

    1 min · Wooden dowel 101339 ×2

    Push 2 dowels into the holes in the middle of the shelf's free face, the side away from the first divider.

  6. Step 6: Slide on the second divider

    1 min

    Slide the second short divider onto the dowels in the shelf, in line with the first divider, until it sits tight.

  7. Step 7: Add the second shelf

    2 min · Wooden dowel 101339 ×2

    Push 2 dowels into the next pair of holes on the long panel and slide the second shelf onto them, against the end of the divider.

  8. Step 8: Dowels for the third divider

    1 min · Wooden dowel 101339 ×2

    Push 2 dowels into the holes in the middle of the second shelf's free face.

  9. Step 9: Slide on the third divider

    1 min

    Slide the third short divider onto the dowels in the second shelf, in line with the others.

  10. Step 10: Add the third shelf

    2 min · Wooden dowel 101339 ×2

    Push 2 dowels into the last pair of shelf holes on the long panel and slide the third shelf onto them, against the end of the divider.

  11. Step 11: Dowels for the last divider

    1 min · Wooden dowel 101339 ×2

    Push 2 dowels into the holes in the middle of the third shelf's free face.

  12. Step 12: Slide on the last divider

    1 min

    Slide the fourth short divider onto the dowels in the third shelf. All four dividers now run in one straight line down the middle.

  13. Step 13: Dowels for the second long panel

    2 min · Wooden dowel 101339 ×8

    Push 2 dowels into the free end of each shelf, 6 in all, and 2 into the free end of the last divider. All 8 should stand straight out.

  14. Step 14: Fit the second long panel

    3 min

    Line the holes of the second long panel up with the 6 shelf dowels and press it on evenly along its length until it sits tight against every shelf.

    Watch out: Start every dowel in its hole before you press. Forcing one end on first bends the dowels and can split the shelf ends.

  15. Step 15: Close the end and screw the corners

    4 min · Hex key 100001 (in the bag) · Connector screw 104321/104322 104321 ×6

    Fit the second short panel over the 2 divider dowels and the ends of both long panels. Drive 4 connector screws through it, then 2 through the first short panel into the second long panel, with the hex key.

    Watch out: Tighten until the panels sit flush and stop. Overtightening strips the hole in the panel end and the corner goes loose.

  16. Step 16: Stick on the felt pads and stand it up

    3 min · 2 people · Felt pad (use 4 of the 8) 10002300 ×4

    Peel 4 felt pads off a sheet and press them onto the marks on the outside of the first short panel, the bottom. Then stand the unit upright with a helper.

    Tip: The manual also shows it lying on its side, 147 cm wide, with 8 pads and its own wall steps. This guide follows the upright version; keep the spare sheet.

  17. Step 17: Screw on the 2 wall brackets

    3 min · Phillips screwdriver · Wall bracket 115753 ×2, Short screw 100372 ×4

    In each top cube, hold a bracket 115753 against the pre-drilled holes at the back, just under the top panel. Drive 2 screws 100372 into each bracket with the Phillips screwdriver.

    Watch out: Tip-over hazard: this unit must be fixed to the wall with the brackets provided. Never use it standing free.

    Tip: The drawing shows one bracket on the left side and one on the middle divider. Use the pairs of small holes you find there.

  18. Step 18: Mark the wall

    3 min · Spirit level, Pencil

    Push the unit against the wall, check it is upright with the level on its side, and mark the wall through the round hole in each bracket with a pencil. Then move the unit away.

  19. Step 19: Fit the wall screws

    8 min · Flat screwdriver

    At each mark, fit a screw and plug that suit your wall; they are not in the bag. Leave each head standing a few millimetres off the wall so a plate can hook over it.

    Watch out: Use pan-head screws. The manual crosses out countersunk heads; they will not hold the plate.

    Tip: Screws and plugs depend on your wall. If you are not sure what yours needs, ask a professional, as the manual says.

  20. Step 20: Hang it on the wall plates

    4 min · Flat screwdriver · Keyhole wall plate 103693 ×2, Bracket cover 115754 ×2

    Hook a wall plate 103693 over each screw head, push the unit back so each plate sits in its bracket, adjust it and tighten the screw with the flat screwdriver. Press a cover over each bracket.

    Watch out: Serious or fatal crushing injuries can occur from furniture tip over. Never leave this unit without both wall attachments in place.