Tools

  • Allen key 100001 (in the box), steps 5, 6, 7, 9, 11, 12, 14, 15 and 16
  • Flat-head screwdriver, steps 12 and 15

Parts (15)

PartCountSizeGoes inNote
Back side, left140 mm widestep 2Gently curved strip with four crossbar slots. Left and right back sides are mirror images.
Back side, right140 mm widestep 4Mirror image of the left back side, four slots for the crossbar tabs.
Back crossbar, top146 × 6 × 1.6 cmstep 2Plain bent crossbar with a tab at each end; it goes in the top slot.
Back crossbar with grip strip146 × 6 × 1.6 cmstep 2The only crossbar with a rough grip strip on its face; second slot from the top.
Back crossbar, third146 × 6 × 1.6 cmstep 3Plain crossbar with end tabs; third slot from the top.
Back crossbar, bottom146 × 6 × 1.6 cmstep 3Plain crossbar with end tabs; the lowest slot.
Seat section, left side140 mm widestep 7Part of the seat section: it comes joined to the right seat side by the grey fabric.
Seat section, right side140 mm widestep 7Part of the seat section, mirror image of the left seat side.
Seat fabric1460 mm widestep 7Grey fabric already fitted between the seat sides, with a sleeve along the front and back edges.
Seat rail, back154 × 3.5 × 1.5 cmstep 8Slightly bent rail with a tab at each end; the two seat rails are the same.
Seat rail, front154 × 3.5 × 1.5 cmstep 8Same as the back seat rail: slightly bent, a tab at each end.
Armrest frame, left150 mm widestep 11The big bent loop: armrest on top, runner on the floor. The largest piece in the box.
Armrest frame, right150 mm widestep 14Mirror image of the left armrest frame.
Base crossbar, front157 × 6 × 2.4 cmstep 12Straight crossbar with two pins and a side hole at each end; looks like the floor crossbar.
Base crossbar, floor157 × 6 × 2.4 cmstep 12Straight crossbar with two pins and a side hole at each end; joins the runners at the back.

Hardware (28 pieces)

Part no.HardwareCountSizeUsed in
100514Barrel nut 100514×4Ø 10 × 14 mmsteps 12 and 15
102319Rubber washer 102319×2Ø 18 × 6 mmsteps 10 and 13
122606Long bolt 122606×4Ø 6 × 100 mmsteps 12 and 15
146654Medium bolt 146654×2Ø 6 × 85 mmsteps 11 and 14
123786Pin with collar 123786×2Ø 8 × 40 mmsteps 10 and 13
119046Short bolt 119046×8Ø 6 × 15 mmsteps 5 and 6
120925Short bolt 120925, slightly bigger×6Ø 8 × 18 mmsteps 7 and 9

Sizes are as drawn in the 3D: diameter × length for fasteners, in millimeters.

The 16 steps

  1. Step 1: Check your parts

    3 min

    Lay the parts on a rug or the flattened box so the bent wood does not scratch. Sort the bolts by number: the two short sizes look alike, and so do the two long ones.

    Tip: The manual says no power drill: turn every bolt by hand with the Allen key. Check the small plastic glide (122526) under each runner is in place.

  2. Step 2: Fit two crossbars into one back side

    3 min

    Lay one curved back side flat, slots up. Push the tabs of the top crossbar and the crossbar with the grip strip into its two upper slots.

    Watch out: Each crossbar is slightly bent. Check the bend against the manual's drawing before you push it in; a flipped crossbar has to come out again.

  3. Step 3: Fit the last two crossbars

    2 min

    Push the tabs of the two plain crossbars into the two lower slots of the same side. Check every tab sits fully down in its slot.

    Watch out: Match the bend of these two crossbars to the drawing as well. All four should curve the same way.

  4. Step 4: Lay the second back side on top

    2 min

    Lower the second curved back side onto the free tabs of all four crossbars and press it down until every tab is in its slot.

    Tip: The second side is a mirror image of the first: its curve should line up with the side underneath.

  5. Step 5: Bolt the top side to the crossbars

    3 min · Allen key 100001 (in the box) · Short bolt 119046 119046 ×4

    Press the side down with both hands and drive a short bolt 119046 through each of the 4 holes into the crossbar tabs. Turn them with the Allen key until snug.

    Watch out: Use the short bolts 119046 here, not the slightly bigger 120925. The manual shows both side by side because they are easy to mix up.

  6. Step 6: Flip the back and bolt the other side

    3 min · Allen key 100001 (in the box) · Short bolt 119046 119046 ×4

    Turn the back over and drive the other 4 short bolts 119046 through the second side into the crossbar tabs, pressing the side down as you go.

    Watch out: Again use 119046, not 120925. Compare the bolt to the drawing before you turn it.

    Tip: This uses the last 4 of the 8 short bolts 119046. If one is left over, a hole was missed.

  7. Step 7: Join the seat section to the back

    4 min · Allen key 100001 (in the box) · Short bolt 120925, slightly bigger 120925 ×2

    Lay the seat section, fabric up, against the lower ends of the back. Fit the ends into each other and drive a short bolt 120925 into each joint with the Allen key, one per side.

    Watch out: These joints take the slightly bigger bolt 120925, not 119046. Check the number before you turn it.

    Tip: The seat section comes with its fabric already fitted between the two curved pieces.

  8. Step 8: Slide the two seat rails into the fabric

    3 min

    Slide one bent seat rail through the fabric sleeve at the front and one through the sleeve at the back. Push each end tab into its corner pocket so it sits on the frame.

    Watch out: Each rail is slightly bent. Fit it with the middle dipping down and the ends up, as in the manual; flipped, it bows the wrong way.

  9. Step 9: Bolt the seat rails to the frame

    3 min · Allen key 100001 (in the box) · Short bolt 120925, slightly bigger 120925 ×4

    Drive a short bolt 120925 down through the tab at each end of both rails into the frame, 4 in all, with the Allen key.

    Watch out: Use 120925 here too, not the smaller 119046.

  10. Step 10: Fit a pin and a washer on the left side

    2 min · Pin with collar 123786 123786 ×1, Rubber washer 102319 102319 ×1

    Turn the frame onto its right side so the left side faces up. Push a pin 123786 into the hole at the front of the seat frame and lay a rubber washer 102319 on the hole at the back.

    Tip: The manual's drawing is small; the simplest reading is that the pin goes where the armrest front will sit, in up to its collar, and the washer sits between frame and armrest.

  11. Step 11: Bolt on the left armrest

    3 min · Allen key 100001 (in the box) · Medium bolt 146654 146654 ×1

    Lay the left armrest frame on top, its front over the pin and its back hole over the washer. Drive a medium bolt 146654 through it into the frame with the Allen key.

    Watch out: Use the medium bolt 146654 here, not the long 122606. The long ones are for the crossbars.

    Tip: Keep the washer on its hole as you lower the armrest; it must end up between the two pieces.

  12. Step 12: Fit both crossbars to the left armrest

    4 min · Allen key 100001 (in the box), Flat-head screwdriver · Barrel nut 100514 100514 ×2, Long bolt 122606 122606 ×2

    Push the pins of the front crossbar and the floor crossbar into the left armrest. Drop a barrel nut 100514 into each crossbar's side hole, line up its slot with the flat screwdriver, then drive a long bolt 122606 into each.

    Watch out: Turn each crossbar so its barrel-nut hole faces outward, as in the manual. Flipped, the hole is hidden and the bolt has nothing to catch.

    Tip: These take the long bolts 122606, not the medium 146654. Turn the barrel nut until the bolt bites, then tighten.

  13. Step 13: Fit a pin and a washer on the right side

    2 min · Pin with collar 123786 123786 ×1, Rubber washer 102319 102319 ×1

    Turn the frame over slowly so the right side faces up. Push the second pin 123786 into the front hole and lay the second rubber washer 102319 on the back hole.

    Tip: The left armrest and crossbars swing wide as you turn it; give yourself room or ask someone to steady it.

  14. Step 14: Bolt on the right armrest

    3 min · Allen key 100001 (in the box) · Medium bolt 146654 146654 ×1

    Lower the right armrest frame onto the pin, the washer and the pins of both crossbars. Drive the second medium bolt 146654 through its back hole into the frame.

    Watch out: Use the medium bolt 146654, not a long 122606. The last two long bolts go into the crossbars next.

  15. Step 15: Bolt the crossbars to the right armrest

    3 min · Allen key 100001 (in the box), Flat-head screwdriver · Barrel nut 100514 100514 ×2, Long bolt 122606 122606 ×2

    Drop a barrel nut 100514 into the side hole at the right end of each crossbar and line up its slot with the flat screwdriver. Drive the last two long bolts 122606 through the armrest into them.

  16. Step 16: Stand it up and tighten all six bolts

    2 min · Allen key 100001 (in the box)

    Stand the chair on its runners. Tighten all six big bolts firmly with the Allen key: one at the back of each armrest and one at each end of both base crossbars.

    Watch out: Do not sit in the chair until all six bolts are tight. A loose joint lets the frame shift under your weight.

    Tip: Fit the cushion last: lay it on the frame and press its back onto the grip strip on the backrest, as the manual's last page shows.