Tools

None: every plug goes on by hand.

Parts (16)

PartCountSizeGoes inNote
TUF GAMING B650-PLUS motherboard1305 × 244 × 1.6 mmstep 2ATX board, 30.5 x 24.4 cm. The edge with the ports faces the back of the case; the headers line the bottom and right edges.
Front USB-C plug (from the case)114 × 11 × 5 mmstep 3A small flat plug on one round cable. It is narrower than the USB 3 plug and fits only U32_C10.
USB 3.2 19-pin plug (from the case)123 × 14 × 9 mmstep 4The widest plug, about 2.3 cm long, on the thickest cable. It is usually marked USB 3.0.
USB 2.0 9-pin plug, first113.5 × 12 × 6 mmstep 5A 9-hole plug marked USB. It has the same shape as the HD AUDIO plug, so read the label.
USB 2.0 9-pin plug, second113.5 × 12 × 6 mmstep 5The second 9-hole USB plug, identical to the first. Either one fits either USB 2.0 header.
HD AUDIO plug (from the case)113.5 × 12 × 6 mmstep 6A 9-hole plug marked HD AUDIO. It has the same size as the USB 2.0 plugs but goes only on AAFP.
Power LED plug112 × 5 × 2.5 mmstep 7A 2-pin plug marked POWER LED or PLED, with + and - printed on it.
HDD LED plug112 × 5 × 2.5 mmstep 7A 2-pin plug marked HDD LED. It is the same size as the power LED plug, so read the label.
Power switch plug112 × 5 × 2.5 mmstep 8A 2-pin plug marked POWER SW. It has no + or - marking.
Reset switch plug112 × 5 × 2.5 mmstep 8A 2-pin plug marked RESET SW. It looks the same as the power switch plug.
Front USB-C cable (case)15 mm widestep 3A thin round cable running from the case's front USB-C port to the small flat plug.
Front USB 3 cable (case)18 mm widestep 4The thickest and stiffest cable from the case, ending in the wide 19-pin plug.
Front USB 2.0 cable, first14 mm widestep 5A thin cable ending in a 9-hole plug marked USB.
Front USB 2.0 cable, second14 mm widestep 5The second thin USB cable, identical to the first.
Front audio cable (case)14 mm widestep 6A thin cable ending in the 9-hole plug marked HD AUDIO, not USB.
Front panel wire bundle (case)16 mm widestep 7A bundle of thin coloured wires that splits into the small 2-pin LED and switch plugs.

The 9 steps

  1. Step 1: Check the board and your case leads

    2 min

    Lay the board on its anti-static bag. Next to it, sort the leads coming from your case's front panel: USB-C, the wide USB 3 plug, the USB 2.0 plugs, HD AUDIO and the small 2-pin panel plugs.

    Tip: Read the label printed on each plug now. The USB 2.0 and HD AUDIO plugs are the same shape, and so are the four 2-pin plugs.

  2. Step 2: Unplug the power and ground yourself

    2 min

    Switch off the power supply and pull its cord from the wall. Wear an anti-static wrist strap or touch the metal of the power supply, then handle the board by its edges with the rear ports toward the back.

    Watch out: Unplug the power cord before you touch any part. The manual warns that skipping this can hurt you and damage the board.

    Tip: If the board is already screwed into the case, work in place. Every header in this guide sits along the bottom and right edges.

  3. Step 3: Plug in the front USB-C lead (U32_C10)

    2 min

    Find the small U32_C10 header on the right edge, just below the 24-pin power connector. Line up the case's USB-C plug with it and push it straight in until it seats.

    Watch out: Push the USB-C plug straight in and never rock it from side to side. This small header breaks easily if you lever it.

    Tip: The manual says the front USB-C module is sold separately. If your case has no front USB-C port, skip this step.

  4. Step 4: Connect the USB 3.2 header (U32G1_89)

    3 min

    Find the wide 19-pin U32G1_89 header just above the USB-C header. Turn the case's thick USB 3 plug so its key matches the gap in the header, then press it straight on until it is fully seated.

    Watch out: These thin pins bend easily. If the plug will not slide on, check the key instead of pushing harder.

    Tip: This header gives two extra front USB 3.2 Gen 1 ports at up to 5 Gb/s.

  5. Step 5: Connect the USB 2.0 headers

    2 min

    Find USB_1415 and USB_1617 on the bottom edge, left of the PANEL header. Push each 9-hole USB plug from the case onto one header, with the blocked hole over the missing pin.

    Watch out: Never connect a 1394 (FireWire) cable to these USB headers. The manual warns that it can damage the board.

    Tip: Each header serves two front USB 2.0 ports at up to 480 Mb/s. If your case has only one USB 2.0 plug, either header works.

  6. Step 6: Connect the front audio header (AAFP)

    2 min

    Find the AAFP header at the far left of the bottom edge. Push the case's HD AUDIO plug onto it, with the blocked hole over the missing pin, until it sits fully down.

    Watch out: The audio plug and the USB 2.0 plugs look alike. Read the label: HD AUDIO goes only on AAFP, at the far left of the bottom edge.

    Tip: The manual recommends an HD Audio front module on this header for HD-quality sound. 7.1 surround also needs one.

  7. Step 7: Fit the power LED and HDD LED plugs

    3 min

    At the PANEL header in the bottom-right corner, push the case's POWER LED plug onto PLED+ and PLED-. Then push the HDD LED plug onto HDD_LED+ and HDD_LED-, the pair that starts at pin 1.

    Watch out: LEDs light only one way round. Put the + side of each plug on the + pin. If an LED stays dark later, turn its plug round.

    Tip: The manual also shows a 3-1 pin PLED position further along the header. Use it if your case's power LED plug has 3 holes.

  8. Step 8: Fit the power switch and reset plugs

    3 min

    Push the case's POWER SW plug onto PWRBTN# and GND, right beside the power LED pins. Push the RESET SW plug onto Ground and RSTCON#, beside the HDD LED pins.

    Watch out: With the power switch plug on the wrong pair, the button does nothing. Check that it sits on PWRBTN# before you close the case.

    Tip: Switch plugs work either way round. If your case has a speaker or an intrusion switch, they go on SPEAKER and CHASSIS at the far end of the header.

  9. Step 9: Check every plug before power on

    2 min

    Look along each header and check that every plug sits fully down and none is one pin off. Check that the power cables are undamaged before you plug the cord back into the wall.

    Watch out: To avoid short circuits, keep clips, screws and staples away from connectors, slots and circuitry, as the manual says.

    Tip: Leave the CLRTC pins on the bottom edge bare. The manual warns that a cap or a short there stops the system from starting.