Tools
- Phillips screwdriver, steps 4, 5, 7, 8 and 10
Parts (22)
| Part | Count | Size | Goes in | Note |
|---|---|---|---|---|
| Case frame with motherboard tray | 1 | 43.3 × 42.6 × 22 cm | step 2 | The steel frame: rear wall, front wall and the motherboard tray. The front I/O, the cable bar, the HDD cage and the two 120 mm fans (C) come fitted in it. |
| Top panel with magnetic dust filter | 1 | 43.3 × 22 × 1 cm | step 2 | One of the three dust filters (B) lies on top; the power and reset buttons sit at its front edge. |
| Floor with feet and PSU dust filter | 1 | 43.3 × 22 × 3 cm | step 2 | The bottom of the case; the slide-out dust filter (B) under the power supply lives here. |
| PSU shroud | 1 | 41.3 × 18.5 cm, 6 mm thick | step 2 | The flat cover over the power supply and the HDD cage; an SSD tray can sit on top of it. |
| Tempered glass side panel (A) | 1 | 43.6 × 43.3 cm, 4 mm thick | step 13 | The see-through side panel. Same size as the solid panel but heavier, and the only one that can break. |
| Solid side panel (F) | 1 | 43.6 × 43.3 cm, 3 mm thick | step 13 | Same size as the glass panel but painted steel; it hides the cables behind the motherboard tray. |
| Front bezel (G) | 1 | 43.6 × 22 × 2 cm | step 11 | The perforated front, 22 cm wide. It pulls off forward on clips; the front dust filter and front fan sit behind it. |
| Motherboard (yours, ATX) | 1 | 30.5 × 24.4 cm, 1.6 mm thick | step 5 | Your own board, not in the box; ATX is 30.5 x 24.4 cm. Its ports go at the rear edge. |
| PCIe card (yours) | 1 | 27 × 11 × 4 cm | step 10 | Your own graphics or expansion card; up to 36 cm long fits. Its metal bracket goes at the rear. |
| Power supply (yours) | 1 | 16 × 15 × 8.6 cm | step 9 | Your own ATX power supply, up to 22 cm long. The side with the fan faces the floor. |
| Hard drive 1 (yours) | 1 | 14.7 × 10.2 × 2.6 cm | step 6 | Your 3.5 in hard drive: bigger and heavier than an SSD, connectors on one short end. |
| Hard drive 2 (yours) | 1 | 14.7 × 10.2 × 2.6 cm | step 6 | The second hard drive; goes in the upper HDD tray. |
| HDD tray, lower (E) | 1 | 15.5 × 10.6 cm, 8 mm thick | step 6 | Plastic sled that ships inside the HDD cage; longer and thicker than an SSD tray. |
| HDD tray, upper (E) | 1 | 15.5 × 10.6 cm, 8 mm thick | step 6 | Identical to the lower HDD tray; it sits in the upper slot of the cage. |
| SSD 1 (yours) | 1 | 10 × 7 cm, 7 mm thick | step 8 | Your 2.5 in SSD: thin and light, much smaller than a hard drive. |
| SSD 2 (yours) | 1 | 10 × 7 cm, 7 mm thick | step 8 | The second 2.5 in SSD; here it goes on the PSU shroud. |
| SSD tray (D), behind the tray | 1 | 11.5 × 8 cm, 2 mm thick | step 8 | Flat steel plate with four screw holes; ships on the back of the motherboard tray. Thinner than an HDD tray. |
| SSD tray (D), on the shroud | 1 | 11.5 × 8 cm, 2 mm thick | step 8 | Identical to the other SSD tray; this one moves onto the PSU shroud. |
| Front USB 3.1 Type-C lead | 1 | 8 mm wide | step 12 | The small flat plug with a latch; the narrowest of the USB plugs. |
| Front USB 3.0 lead | 1 | 6 mm wide | step 12 | The big blocky plug on a thick cable; wider than the Type-C plug. |
| Front HD Audio lead | 1 | 5 mm wide | step 12 | A small one-piece plug with one blocked pin, labelled HD AUDIO; it reaches the bottom rear of the board. |
| Power SW, Reset SW and Power LED leads | 1 | 10 mm wide | step 12 | The tiny separate two-wire plugs: POWER SW, RESET SW, POWER LED + and POWER LED −. |
Hardware (36 pieces)
| Hardware | Count | Size | Used in |
|---|---|---|---|
| MBD / HDD screw (9 used, 18 in bag) | ×9 | Ø 3.5 × 6 mm | step 5 |
| ODD / SSD screw | ×8 | Ø 3 × 4 mm | step 8 |
| Thumbscrew | ×4 | Ø 3.5 × 10 mm | step 9 |
| Cable tie | ×12 | Ø 4 × 100 mm | step 12 |
| Velcro strap | ×3 | Ø 12 × 150 mm | step 12 |
Sizes are as drawn in the 3D: diameter × length for fasteners, in millimeters.
The 13 steps
-
Step 1: Check the case and the accessory kit
Stand the case on a clear table and lay your own motherboard, power supply, PCIe card and drives beside it. Count the accessory kit: 20 fan screws, 18 MBD/HDD screws, 8 ODD/SSD screws, 4 thumbscrews, 3 standoffs, 12 cable ties, 3 velcro straps, 8 washers.
Tip: The fan screws, washers, 3 extra standoffs and 9 spare MBD/HDD screws are for options this manual does not build: extra fans, radiators, an E-ATX board. Keep them in the bag.
-
Step 2: Choose which side gets the glass
Stand the case upright on the table. The tempered glass and the solid panel fit either side: glass on the left shows off the motherboard (A), or swap the two (B). Decide now; you fit them at the end.
Tip: With the glass on the left, the solid panel on the right hides the cables behind the motherboard tray.
-
Step 3: Take off both side panels
At the back of each panel, undo the thumbscrew (1). Swing the rear edge out (2), then lift the panel up off its hooks at the front (3). Lay both panels flat on a soft cloth.
Watch out: Tempered glass. Lay the glass panel flat on a cloth, never on its edge or a hard floor. A knock on a corner can shatter it.
-
Step 4: Set the cable bar for your board
For ATX, Micro-ATX and Mini-ITX boards, leave the cable bar where it is. For an E-ATX board (30.5 x 27.7 cm), undo the bar's screws (1), slide it toward the front into the E-ATX holes (2) and refit the screws.
Tip: Not sure which you have? Measure the board. ATX is 24.4 cm wide; anything wider is E-ATX and needs the bar moved.
-
Step 5: Install the motherboard
Lay the case on its right side, open side up. Line the board's ports up with the rear opening and lower it onto the standoffs. Drive 9 MBD/HDD screws through the board's holes, hand-tight.
Watch out: Check there is a standoff under every hole in your board and none where the board has no hole. A stray standoff can short the board.
Tip: Fit the CPU, memory and cooler while the board lies on its box, and fit a loose I/O shield first. An E-ATX board also takes the 3 standoffs from the bag.
-
Step 6: Install the hard drives
From the right side, pull an HDD tray out of the cage under the shroud. Set a hard drive in it, connectors facing out, and press it down until the tray's pins hold it. Slide the tray back in until it stops, then do the same with the second.
Tip: The pins on the tray sides go into the drive's side screw holes. Flex the tray sides open a little to drop the drive in.
-
Step 7: Move the HDD cage if you need room
Only if a front radiator or extra front fans need the space: undo the screws under the HDD cage, slide the cage toward the back of the case and refit the screws. Otherwise leave it where it is.
Tip: The drawing shows the cage sliding along the floor; the simplest reading is back toward the power supply. Check your PSU and its cables still fit before you tighten.
-
Step 8: Mount the SSDs on their trays
Take an SSD tray off its mount and screw a 2.5 in SSD to it from underneath with 4 ODD/SSD screws. Put the tray back behind the motherboard tray (A) or on top of the PSU shroud (B). Do the same with the second SSD.
Tip: Use the short ODD/SSD screws here, not the MBD/HDD screws. Point each SSD's connectors toward the cable you will run to it.
-
Step 9: Slide in the power supply
From the right side, slide the power supply into the bottom of the case, fan facing down, until its back sits flat against the rear wall. Fix it from the outside with 4 thumbscrews, hand-tight.
Watch out: Keep the power supply unplugged and its switch at 0 until the final step.
Tip: The drawing shows no PSU screws. The four bag thumbscrews fit the standard PSU holes; the screws that came with your power supply work too.
-
Step 10: Fit your PCIe card
At the back, undo the two screws that hold the slot covers and take out as many covers as your card is wide. Push the card into the top PCIe slot until the latch clicks, then refit the two screws through its bracket.
Watch out: Press the card fully home before you screw the bracket. A card held only by its bracket sits loose in the slot and may not be detected.
-
Step 11: Take off and refit the front bezel
When you need the front fans or the front dust filter, grip the bezel at its edge and pull it straight forward off its clips. Press it back on square until every clip snaps in.
Tip: Behind the bezel sit the front dust filter and the included 120 mm front fan. The front takes up to three 120 mm or two 140 mm fans.
-
Step 12: Connect the front I/O leads
Route the front-panel leads behind the motherboard tray to your board: USB 3.1 Type-C, USB 3.0, HD Audio, then Power SW, Reset SW and Power LED + and −. Match each plug to the header named in your board's manual, then bundle the leads with ties and straps.
Watch out: Only the Power LED + and − leads have a polarity. Power SW and Reset SW work either way round, but a reversed LED stays dark.
Tip: Push the USB 3.0 plug straight in by its body, never by the cable; its pins bend easily.
-
Step 13: Refit the side panels and test
Hook each panel on at the front, swing the rear edge shut and refit its thumbscrew. Plug in the mains lead, switch the PSU to I and press the power button: the fans spin and the power LED lights.
Watch out: Fit both panels before you plug in. If the PC does not start, switch the PSU off and unplug at the wall before you touch any lead.
