Tools
- Phillips screwdriver, steps 7, 8, 9, 10, 11 and 13
Parts (25)
| Part | Count | Size | Goes in | Note |
|---|---|---|---|---|
| Case chassis (rear wall and motherboard tray) | 1 | 45.5 × 32 × 28 cm | step 2 | The steel frame: the rear wall with the slots and the tray the motherboard screws to. It is one piece with the floor. |
| Case floor and feet | 1 | 46.6 × 29 × 3.5 cm | step 2 | The floor with the bottom filter and the four feet. It is one piece with the chassis and does not come off. |
| Front tempered glass panel | 1 | 45.5 × 22.1 cm, 4 mm thick | step 2 | The narrower glass at the front. It stays on the case; only the wider side glass comes off. |
| Tempered glass side panel | 1 | 46 × 45.5 cm, 4 mm thick | step 19 | The wide glass on the left side. It lifts off; the front glass does not. |
| Right side panel (mesh) | 1 | 46.6 × 45.5 cm, 6 mm thick | step 19 | The perforated steel panel on the right, over the side fans. It is about the size of the glass side panel but opaque. |
| Top mesh panel | 1 | 46.6 × 29 cm, 8 mm thick | step 19 | The flat perforated lid with the top filter under it, the only panel that lies horizontal. |
| Front I/O module | 1 | 12 × 5 × 2 cm | step 3 | The ports and the power switch at the top front right. Its cable bundle carries the four front-panel plugs. |
| Rear exhaust fan, 120 mm | 1 | 12 × 12 × 2.5 cm | step 2 | Fitted at the factory at the back of the main chamber, above the slots. It is the only fan that faces the rear. |
| Motherboard (yours, ATX shown) | 1 | 30.5 × 24.4 cm, 4 mm thick | step 7 | Your board. The case takes ATX, Micro-ATX and mini-ITX. The edge with the rear ports goes to the back. |
| Graphics card (yours) | 1 | 30 × 12 × 5 cm | step 10 | Your card. Cards up to 43.5 cm long fit. Its fans face down once it is installed. |
| Power supply (yours) | 1 | 16 × 15 × 8.6 cm | step 11 | Your PSU, up to 20 cm long. The side with the fan faces the right side panel. |
| Top cooler bracket | 1 | 40 × 17 × 1.5 cm | step 13 | The flat steel tray under the top panel with rows of fan holes. It holds the top fans or a radiator. |
| Top fan 120 mm (yours), rear | 1 | 12 × 12 × 2.5 cm | step 13 | A fan you add on top. It is the same size as the side fans but not fitted at the factory. |
| Top fan 120 mm (yours), middle | 1 | 12 × 12 × 2.5 cm | step 13 | A fan you add on top. It is the same size as the side fans but not fitted at the factory. |
| Top fan 120 mm (yours), front | 1 | 12 × 12 × 2.5 cm | step 13 | A fan you add on top. It is the same size as the side fans but not fitted at the factory. |
| SSD mounting bracket | 1 | 40 × 8 cm, 3 mm thick | step 8 | The narrow, tall plate at the front of the rear chamber. It holds up to four 2.5-inch SSDs and is thinner than the side cooler bracket. |
| 2.5-inch SSD (yours), on the bracket | 1 | 10 × 7 cm, 7 mm thick | step 8 | The same kind of drive as the SSD in the cage. This one goes on the SSD bracket. |
| Drive cage | 1 | 15 × 11 × 8 cm | step 9 | The box at the bottom of the rear chamber marked LIFT UP TO RELEASE. It takes two drives. |
| 3.5-inch hard drive (yours) | 1 | 14.7 × 10.2 × 2.6 cm | step 9 | The big metal drive. It goes in the drive cage with B screws. |
| 2.5-inch SSD (yours), in the cage | 1 | 10 × 7 cm, 7 mm thick | step 9 | The same kind of drive as the SSD on the bracket. This one goes in the second slot of the drive cage. |
| Right side cooler bracket | 1 | 40 × 13 × 1 cm | step 14 | The tall bracket behind the right side panel at the front. It carries the three side fans or a radiator and is wider than the SSD bracket. |
| Side intake fan 120 mm, bottom | 1 | 12 × 12 × 2.5 cm | step 14 | One of the three fans fitted at the factory on the side cooler bracket. |
| Side intake fan 120 mm, middle | 1 | 12 × 12 × 2.5 cm | step 14 | One of the three fans fitted at the factory on the side cooler bracket. |
| Side intake fan 120 mm, top | 1 | 12 × 12 × 2.5 cm | step 14 | One of the three fans fitted at the factory on the side cooler bracket. |
| Cable bar | 1 | 30 mm wide | step 19 | The bent steel bar with a jog in the middle at the front edge of the tray. It hides the cables and pulls out to the right. |
Hardware (49 pieces)
| Part no. | Hardware | Count | Size | Used in |
|---|---|---|---|---|
| A | A: Hexagon screw 6-32 × 6 mm (power supply) | ×4 | Ø 3.5 × 6 mm | step 11 |
| B | B: 6-32 × 5 mm screw (15 used, 17 in bag) | ×15 | Ø 3.5 × 5 mm | steps 7, 9 and 10 |
| C | C: M3 × 5 mm screw (8 used, 24 in bag) | ×8 | Ø 3 × 5 mm | steps 8 and 9 |
| D | D: Screw KB5 × 10 mm (fans) | ×12 | Ø 5 × 10 mm | step 13 |
| E | E: Cable tie | ×10 | Ø 4 × 120 mm | step 19 |
Sizes are as drawn in the 3D: diameter × length for fasteners, in millimeters.
The 19 steps
-
Step 1: Check the case and the screw bag
Unbox the case and find the accessory box inside. Sort screws A to E and the cable ties into bowls, and lay your motherboard, graphics card, power supply, drives and fans beside the case.
Tip: The case arrives in one piece with its panels, brackets and side fans fitted. The mat shows each piece apart so you can learn it, and each one is placed in the step that uses it.
-
Step 2: Get to know the front-panel plugs
Stand the case upright on a table. Find the four front I/O plugs in its cable bundle: the F_PANEL block for the Intel-standard front-panel header, the USB 3.2 Gen 2 Type-C plug, the USB 3.2 Gen 1 Type-A plug and the HD audio plug.
Tip: Each plug fits its motherboard header only one way: match the blocked pin on HD audio and the key on the USB plugs. You plug them in once the motherboard is screwed down.
-
Step 3: Find the buttons and ports on top
At the top front right of the case you'll find a headset jack, a USB 3.2 Gen 2 Type-C port, two USB 3.2 Gen 1 Type-A ports and the power switch with its power LED ring.
-
Step 4: Take off the side and top panels
At the back, loosen the two thumbscrews at the top corners. Swing the glass side panel and the right side panel out at the top and lift them off their bottom edges, then lift the top panel off.
Watch out: Hold the glass panel by both edges and lay it flat on a soft cloth. Never stand tempered glass on a corner.
Tip: The panels wait on the mat until the last step, when they go back on.
-
Step 5: Remove the cable bar
On the right side, loosen the four screws that hold the cable bar, two near the top and two lower down. Pull the bar straight out through the open right side of the case.
Tip: This opens the space at the front of the tray for the board, the drives and the cables. The bar goes back in the last step.
-
Step 6: Learn the cable channels
Behind the motherboard tray are four cable channels. The 8-pin and fan cables run along the top, and the 24-pin and SATA cables run down the middle. The front I/O cables run along the bottom with SATA and up the front beside the fans.
Tip: Route each cable through its channel as you fit the parts. You tie them down with the cable ties at the end.
-
Step 7: Screw in the motherboard
Lay the case on its right side, glass side up. Lower the motherboard onto the standoffs with its rear ports at the back, line up the holes and drive the nine B screws.
Watch out: The tray marks each standoff A (ATX), U (Micro-ATX) or I (mini-ITX). Use only the ones for your board; a standoff under a spot with no hole can short the board.
Tip: Start all nine screws loosely before tightening any. Then plug in the four front I/O plugs, routed through the front I/O channels.
-
Step 8: Mount an SSD on the SSD bracket
On the right side, loosen the two thumbscrews at the top and bottom of the SSD bracket and swing it out, or lift it out completely. Screw the SSD to the bracket with four C screws, then put the bracket back and tighten the thumbscrews.
Tip: The bracket holds up to four 2.5-inch SSDs and the drive cage two more. The 24 C screws cover all six, so you'll have spares.
-
Step 9: Fit drives in the drive cage
Loosen the thumbscrew on the drive cage, lift the cage up and take it out. Each of its two slots takes a 3.5-inch drive with four B screws or a 2.5-inch drive with four C screws. Hook the cage back in and tighten the thumbscrew.
Watch out: Don't pull the cage straight out, because it is hooked in. Lift it up first, as its LIFT UP TO RELEASE label says.
Tip: The exploded view labels this cage 5, Rear Exhaust Fan, which looks like a typo. Use the B screws for the 3.5-inch drive and the C screws for the 2.5-inch drive.
-
Step 10: Install the graphics card
With the case on its right side, take out the slot covers in line with your card. Lower the card straight into the PCIe x16 slot until the latch clicks, then fix its bracket with two B screws.
Watch out: Press the card down until the slot latch clicks before you drive the screws. A card that is screwed in only half-seated may not be detected.
Tip: Cards up to 43.5 cm long fit.
-
Step 11: Install the power supply
From the right side, slide the power supply into the rear chamber up to its frame at the back, with its fan facing the right side panel. Drive the four A screws through the back of the case into the power supply.
Watch out: Install the PSU with the fan facing outward, toward the mesh side panel. The manual marks this as important.
Tip: Power supplies up to 20 cm long fit.
-
Step 12: Plan your fans and radiators
Fans fit 3 × 120 mm or 2 × 140 mm on top, 3 × 120 mm on the side, 1 × 120 mm at the rear and 3 × 120 mm or 2 × 140 mm on the bottom. Radiators fit up to 360 mm on top and bottom, 120, 240 or 360 mm on the side and up to 120 mm at the rear.
Tip: The case comes with the three side fans and the rear fan. This build adds three 120 mm fans on top, and the radiator steps show the other choices.
-
Step 13: Fit three fans on the top bracket
Loosen the two screws on top of the case and lift the top cooler bracket out. Screw three 120 mm fans to its underside with four D screws each, then lower the bracket back in and tighten its two screws.
Watch out: Check the airflow arrows on the fan frames before you screw them on, so all three fans blow the same way.
Tip: Loosen the two screws a few turns but leave them in. The bracket sits on keyhole slots, so slide it and lift it off.
-
Step 14: Refit the side fan bracket
The three side fans come fitted on the right side cooler bracket. To change them, loosen the thumbscrews at the top and bottom, swing the bracket out and screw each fan on with four screws. Swing it back in and tighten the thumbscrews.
Tip: This build used the bag's 12 D fan screws on top. The factory side fans keep their own screws.
-
Step 15: Option: fit fans on the bottom
To add bottom fans, lay the case on its side and screw three 120 mm or two 140 mm fans up into the floor with four D screws each, through the holes underneath.
Tip: This build has no bottom fans, so nothing moves here. You'd need 12 more fan screws, because the bag's 12 D screws went to the top fans.
-
Step 16: Option: fit a radiator on the bottom
A bottom radiator up to 360 mm goes in the same place. Set it on the floor of the case with its fans and screw it in from underneath with the screws that come with your AIO cooler.
Tip: Nothing moves here because this build uses fans. Radiator screws are not in the case's bag.
-
Step 17: Option: fit a radiator on the top
For a top radiator up to 360 mm, lift out the top cooler bracket as in the top fan step. Screw the radiator and its fans to the bracket with your AIO cooler's screws, then lower it back in.
Tip: This build has fans on the top bracket, so nothing moves here.
-
Step 18: Option: fit a radiator on the side
For a side radiator of 120, 240 or 360 mm, swing out the side cooler bracket. Screw the radiator to one face and the fans to the other with your AIO cooler's screws, then swing the bracket back in.
Tip: This build keeps the factory side fans, so nothing moves here.
-
Step 19: Tie the cables and close the case
Tie the cable bundles to their channels with the cable ties. Push the cable bar back in and tighten its screws, then set the top panel on. Hook both side panels on at the bottom, swing them closed and tighten the two rear thumbscrews.
Watch out: Check that no cable sticks out past the cable bar or the tray edge before you close the glass panel. A pinched cable stops the panel from seating.
Tip: This is the panel removal from step 4 done backwards. The manual shows only the removal.
