Tools
- Allen keys H2 and H1.5 (accessory box), steps 3, 7, 8, 11 and 14
- Scissors or side cutters, step 5
Parts (18)
| Part | Count | Size | Goes in | Note |
|---|---|---|---|---|
| A1 base housing | 1 | 39 × 31 × 6 cm | step 2 | The low wide box with the heatbed on top. The touch screen is folded against its right side, near the front. |
| Heatbed | 1 | 26 × 26 × 1.2 cm | step 2 | Arrives fitted on the base housing. It slides front to back once you unlock it. |
| Build plate | 1 | 27.5 × 26.5 cm, 2 mm thick | step 2 | The thin flexible sheet. The tab with the slot goes to the back, the small logo to the front right. |
| A1 printer frame | 1 | 43 × 40 × 5 cm | step 4 | The tall arch with the X-axis and toolhead already on it. The biggest piece in the box. |
| X-axis rail | 1 | 42 × 4 × 3 cm | step 4 | Arrives fixed across the frame. The rail the toolhead runs along. |
| Toolhead | 1 | 10.8 × 6.5 × 5 cm | step 4 | Arrives at the left end of the X-axis, held by a zip tie and cardboard. |
| Y-axis cover | 1 | 24 × 14 cm, 3 mm thick | step 9 | The thin strip over the rails at the back of the base. It comes out and goes back in. |
| Cable box | 1 | 7 × 5 × 1.5 cm | step 11 | The small box hanging on a cable from the frame, with a Type-C plug and 2 clips. |
| Z Motor harness (yellow) | 1 | 4 mm wide | step 12 | Yellow lead. It goes into the yellow Z Motor socket. |
| X Motor harness (green) | 1 | 4 mm wide | step 12 | Green lead. It goes into the green X Motor socket. |
| Camera harness (white) | 1 | 4 mm wide | step 12 | White lead. It goes into the white Camera socket. |
| Touch screen | 1 | 9 × 6.5 × 1.2 cm | step 13 | Attached to the base housing and folded against its right side until you fold it out. |
| Purge wiper | 1 | 6 × 5 × 4 cm | step 14 | The small unit with an angled arm. It hangs under the left end of the X-axis. |
| Spool holder arm | 1 | 9 × 3 × 3 cm | step 18 | The long arm with a clip at its foot. The shaft comes as a separate piece. |
| Spool holder shaft | 1 | Ø 2 × 9 cm | step 18 | The short rod. It pushes into the hole at the joint of the spool holder arm. |
| 600 mm PTFE tube | 1 | 4 mm wide | step 18 | The loose 600 mm white tube, not the tube already fitted to the toolhead. |
| Cable organizer | 1 | Ø 3 × 0.5 cm | step 18 | The flower-shaped clip with five round cut-outs, from the accessory box. |
| Power cable | 1 | 8 mm wide | step 15 | The black mains lead. It is the very last thing you plug in. |
Hardware (13 pieces)
| Hardware | Count | Size | Used in |
|---|---|---|---|
| M3-12 screw (for purge wiper) | ×1 | Ø 3 × 12 mm | step 14 |
| ST3-23 screw (12 used, 1 spare) | ×12 | Ø 3 × 23 mm | steps 7 and 8 |
Sizes are as drawn in the 3D: diameter × length for fasteners, in millimeters.
The 19 steps
-
Step 1: Check what's in the box
Unpack onto a clear table. Check the base housing, printer frame, build plate, spool holder, purge wiper, power cable, 600 mm PTFE tube, sample filament and accessory box against the list, and tip the screws into a bowl.
Watch out: Do not connect the power cable until assembly is complete.
Tip: You use 12 of the 13 ST3-23 screws, so one is spare. The 2 BT2.6-8 screws are for the scraper blade.
-
Step 2: Fit the build plate
Set the base housing flat on the table. Lay the build plate on the heatbed the right way round and line its edges up with the heatbed.
Watch out: The plate fits one way only: the tab with the slot goes to the back, the small logo to the front right.
-
Step 3: Unlock the heatbed
Tip the base housing 90 degrees onto the side away from the screen. With the H2 Allen key, remove the 4 highlighted screws on the bottom to unlock the heatbed, then set the base flat again.
Watch out: Take care as the heatbed comes free. Put the foam padding from the package against it so it cannot swing.
-
Step 4: Join the base housing and the frame
Stand the printer frame on the table. Tilt the base housing about 45 degrees, pass it through the frame and line up its slot with the frame, then lower it slowly until it sits flush with the frame on the table.
Watch out: Use the screen as your guide: it must end up at the front right. If one side of the base sits high, lift it and line up the slot again.
Tip: The animation moves the frame onto the base; in real life the frame stays on the table and you move the base.
-
Step 5: Unlock the toolhead
Cut the zip tie and the cardboard wrapped around the toolhead and the X-axis. Then remove the 7 zip ties and the 2 foam pads on the printer frame.
Watch out: Cut only the zip ties, never the cables or the tube running beside them.
-
Step 6: Remove the Y-axis cover
Push the heatbed all the way to the front, the screen end. Open the Y-axis cover at the back of the base and pull it out gently, then lay it on the mat.
Watch out: Pull the cover out slowly and keep it straight. A bent cover will not slide back in later.
-
Step 7: Lock the base housing: 10 screws
Drive 10 ST3-23 screws into the holes the manual marks in green: 8 along the rails and 1 on each side by the frame feet. Then push the heatbed to the other end, the back.
Watch out: Drive them snug, not hard. They are self-tapping screws and too much force strips the hole.
Tip: The manual does not name a key for these. Use the one that sits snugly in the screw head, most likely the H2.
-
Step 8: Lock the base housing: last 2 screws
With the heatbed pushed to the back, drive the last 2 ST3-23 screws into the two holes now showing in the front of the rail channel.
-
Step 9: Put the Y-axis cover back
Push the heatbed fully to the front again. Gently slide the Y-axis cover back into place over the rails.
Watch out: Line up the clip shown in the manual before you push the cover home. A cover that misses the clip will not sit flat.
-
Step 10: Lay the printer on its back
Cover the table with cardboard. Turn the A1 90 degrees onto its back and lay it along the edge of the table, so the bottom of the base housing faces out over the edge.
Watch out: Make sure the printer is secure on the table the whole time you work on it like this.
-
Step 11: Plug in the cable box
Line up the 2 clips on the cable box with the holes in the bottom of the base housing. Slide the box up until the Type-C cable clicks in, check it sits flush in the slot, then tighten the screw already fitted in it.
Watch out: Do not force it. If the Type-C plug does not click in easily, slide the box back and line up the 2 clips again.
-
Step 12: Plug in the three harnesses
Plug the 3 harnesses into the sockets of the same colour. Tuck the leads into the cable slot, then close the cover.
Watch out: Match the colours: yellow to Z Motor, green to X Motor, white to Camera. A swapped plug means the printer will not move or see.
-
Step 13: Stand it up and fold out the screen
Stand the printer back on its feet. Fold the touch screen out from the right side of the base and make sure it sits in place as the manual shows.
Tip: The manual shows the printer upright from this step on. Set it down gently on all its feet.
-
Step 14: Fit the purge wiper
Push the toolhead to the middle of the rail to make room. Slide the purge wiper into the slot at the left end of the X-axis, then fix it from below with the M3-12 screw.
Watch out: Use the M3-12 screw for this, not a spare ST3-23. The long screw will not hold the wiper properly.
-
Step 15: Power on
Plug the power cable into the socket on the back of the base and switch the A1 on with the power switch beside it.
Watch out: Clear 54.5 cm of space front to back before you switch on. The heatbed slides that far and needs the room to move safely.
-
Step 16: Connect to Wi-Fi
Follow the setup on the screen until you reach Network, then press Select Wi-Fi. Pick your network, type the password and press OK.
Tip: The A1 only joins 2.4 GHz Wi-Fi. If your network is missing, look for its 2.4 GHz name.
-
Step 17: Bind the printer and calibrate
Download the Bambu Handy app, register and log in. Scan the QR code on the printer's screen to bind it to your account, then follow the screen to run the first calibration.
Tip: Vibration and noise during calibration are normal. Your phone must be on the same network as the printer to find it.
-
Step 18: Fit the spool holder and PTFE tube
Push the shaft into the spool holder and fit it where the manual shows. Join any toolhead inlet to the filament guide with the 600 mm PTFE tube, clip it with the cable organizer, hang your spool and feed the filament into the tube.
Tip: This setup is for printing without an AMS. Any one of the four toolhead inlets works.
-
Step 19: Start your first print
Press Print Files and pick one of the preloaded models. Turn on Bed leveling, turn on Use AMS only if you print from an AMS, and turn on Timelapse if you want a video.
Watch out: Keep your hands clear while it prints. The heatbed slides back and forth and the nozzle can reach 300 °C.
