Tools

  • Two wrenches or a socket set for the 5/8 in nuts and bolts, steps 3 and 7

Parts (13)

PartCountSizeGoes inNote
Rack panel, left [1]1228.6 × 116 × 5.1 cmstep 2One of two identical welded panels. It stands on the left with its feet pointing out front and back.
Rack panel, right [1]1228.6 × 116 × 5.1 cmstep 2Identical to the left panel. It stands on the right with its feet pointing out front and back.
Fat/skinny parallel bar, 109 cm (43 in) [4]1109.2 × 30.5 × 5.1 cmstep 2Two bars side by side, one fat and one skinny, joined by a bolt plate at each end.
J cup, LEFT [3]120 × 8 × 6 cmstep 4Mirror image of the RIGHT cup. Part 3 goes on the left panel.
J cup, RIGHT [2]120 × 8 × 6 cmstep 4Mirror image of the LEFT cup. Part 2 goes on the right panel.
Band peg [9]4Ø 1.6 × 23 cmstep 5Short peg with a T handle, about 23 cm. Much shorter than the safety pins.
Safety pipe [10]2Ø 4.8 × 76.2 cmstep 6Hollow straight pipe about 76 cm long. The safety pin runs through it.
Safety pin [11]215 mm widestep 6Long thin rod with a bent handle at one end. Longer and thinner than the safety pipe.

Hardware (16 pieces)

Part no.HardwareCountSizeUsed in
8Hex screw 1.6 x 8.9 cm (5/8 x 3.5 in) [8]×4Ø 15.9 × 88.9 mmstep 2
5Flat washer 1.6 cm (5/8 in) [5]×4Ø 34 × 3 mmstep 2
6Lock washer 1.6 cm (5/8 in) [6]×4Ø 29 × 4 mmstep 3
7Hex nut 1.6 cm (5/8 in) [7]×4Ø 24 × 14 mmstep 3

Sizes are as drawn in the 3D: diameter × length for fasteners, in millimeters.

The 7 steps

  1. Step 1: Check your parts

    5 min

    Lay out the two rack panels, the parallel bar, both J cups, four band pegs, two safety pipes and two safety pins. Count 4 hex screws, 4 flat washers, 4 lock washers and 4 hex nuts.

    Tip: The J cups are mirror images: LEFT is part 3 and RIGHT is part 2. Keep each one on its own side of the mat.

  2. Step 2: Stand the panels and fit the parallel bar

    10 min · 2 people · Hex screw 1.6 x 8.9 cm (5/8 x 3.5 in) [8] 8 ×4, Flat washer 1.6 cm (5/8 in) [5] 5 ×4

    With a helper, stand both rack panels up about 110 cm apart, feet pointing out front and back. Hold the fat/skinny bar between the top crossmembers and push a hex screw with a flat washer through each panel from the outside into the bar's end plate.

    Watch out: Ensure the rack feet point out as shown in the manual's detail drawing before you lift the bar into place.

    Tip: Two screws per side, one each side of the bars. Keep a hand on each panel until the screws are through.

  3. Step 3: Add lock washers and nuts, snug only

    6 min · Two wrenches or a socket set for the 5/8 in nuts and bolts · Lock washer 1.6 cm (5/8 in) [6] 6 ×4, Hex nut 1.6 cm (5/8 in) [7] 7 ×4

    On the inside of each end plate, slide a lock washer and then a hex nut onto each of the four screws. Run the nuts on until they are snug, holding the screw head with the second wrench.

    Watch out: Do not fully tighten the hardware until the entire rack is assembled. This makes sure the rack sits level on the floor.

    Tip: Do not bolt the rack to the floor yet. That comes after every bolt is fully tightened.

  4. Step 4: Hang the left and right J cups

    2 min

    Hook the LEFT J cup [3] onto the front upright of the left panel and the RIGHT J cup [2] onto the right panel, at the same hole number. Push the pin into the hole and let the cup drop so it sits flat on the upright.

    Watch out: Ensure each J cup is securely attached before use, with its pin all the way in and the cup sitting flat against the upright.

    Tip: Count holes from the floor so both cups match. The drawing shows them on the inner face of the uprights, cups facing into the rack.

  5. Step 5: Insert the four band pegs

    2 min

    Push a band peg through a lower hole of each of the four uprights, from inside the rack, until the T handle stops against the upright. The long end sticks out the side.

    Tip: Use the same low hole on every upright so bands pull evenly.

  6. Step 6: Fit the safety pipes and pins

    4 min

    Lower a safety pipe between the two uprights of each panel, lined up with a pair of holes. Slide a safety pin from the front through the upright, through the pipe and into the back upright to secure it.

    Watch out: Set both pipes at the same hole on both panels and push each pin all the way through to the back upright, or the pipe is not secured in place.

    Tip: Pick a height just below the lowest point of the bar in your lift.

  7. Step 7: Tighten everything and anchor to the floor

    15 min · Two wrenches or a socket set for the 5/8 in nuts and bolts

    Fully tighten all four hex nuts with both wrenches. Then anchor the rack to a solid concrete floor through the holes in its feet, using 1 x 8.9 cm (3/8 x 3.5 in) concrete wedge anchors, which are not included.

    Watch out: This unit must be anchored for use. Misuse of this product can result in severe injury.

    Tip: On rubber flooring, cut out a section under each foot so the feet anchor directly to the concrete.