Tools
- Phillips screwdriver, steps 2, 3 and 5
Parts (11)
| Part | Count | Size | Goes in | Note |
|---|---|---|---|---|
| Motherboard (AM5) | 1 | 30.5 × 24.4 cm, 1.6 mm thick | step 2 | Your AM5 motherboard. The AMD stock backplate stays screwed to its rear side. |
| CPU in the AM5 socket | 1 | 4 × 4 cm, 8.4 mm thick | step 2 | Already locked in the socket. The paste goes on its silver lid. |
| NM-AMB12a mounting bar | 1 | 8 × 1.6 cm, 3 mm thick | step 3 | Marked NORTH with a CPU arrow; goes on the north (top) side. Same size as NM-AMB12b. |
| NM-AMB12b mounting bar | 1 | 8 × 1.6 cm, 3 mm thick | step 3 | Marked SOUTH with a CPU arrow; goes on the south (bottom) side. Same size as NM-AMB12a. |
| Heatsink base and screw bar | 1 | 10.4 × 4.5 × 1.3 cm | step 5 | The base under the fin stacks, one piece with the heatsink. It ships with a protection cover on it. |
| Heatsink fin stacks | 1 | 15 × 14.8 × 13.5 cm | step 5 | Two fin stacks joined by heatpipes. The gap in the middle holds the centre fan. |
| Centre fan | 1 | 15 × 14 × 2.5 cm | step 6 | Arrives clipped between the fin stacks. Identical to the second fan. |
| Second fan | 1 | 15 × 14 × 2.5 cm | step 6 | Same fan as the centre fan; this one clips to the outer face of the front fin stack. |
| Centre fan cable | 1 | 4 mm wide | step 7 | The lead coming out of the centre fan. |
| Second fan cable | 1 | 4 mm wide | step 7 | The lead coming out of the second fan. |
| NA-YC1 splitter cable | 1 | 4 mm wide | step 7 | Y-shaped cable: two fan plugs on one side, one header plug on the other. |
Hardware (17 pieces)
| Part no. | Hardware | Count | Size | Used in |
|---|---|---|---|---|
| NM-APS4 | NM-APS4 grey plastic spacer | ×4 | Ø 9 × 5 mm | step 3 |
| NM-ALS1 | NM-ALS1 long screw | ×4 | Ø 3.5 × 15 mm | step 3 |
| NT-H1 | NT-H1 paste dot, about 2 mm | ×4 | Ø 2 × 0.5 mm | step 4 |
| NT-H1 | NT-H1 paste dot, 3 to 4 mm | ×1 | Ø 3.5 × 0.8 mm | step 4 |
| Heatsink screw (fitted to the heatsink) | ×2 | Ø 4 × 20 mm | step 5 | |
| Steel fan clip | ×2 | Ø 2 × 130 mm | step 6 |
Sizes are as drawn in the 3D: diameter × length for fasteners, in millimeters.
The 8 steps
-
Step 1: Check the AM5 parts
Lay out the heatsink, both fans, the NA-YC1 splitter, the NT-H1 paste and the AMD bag: bars NM-AMB12a and NM-AMB12b, 4 grey NM-APS4 spacers and 4 NM-ALS1 long screws. The Intel backplate and spacers stay in the box.
Tip: Before you start, check your motherboard, CPU, RAM and case on ncc.noctua.at so the cooler fits.
-
Step 2: Remove the stock retention module
Lay the motherboard flat. If the stock AMD retention module is still fitted, unscrew it from the backplate and set it aside. On AM5 the stock backplate is screwed to the socket, so it stays in place.
Watch out: Keep the stock backplate on the back of the board. The Noctua mounting bars screw straight into its threads.
-
Step 3: Fit the spacers and mounting bars
Slide the 4 grey NM-APS4 spacers onto the backplate threads. Lay NM-AMB12a (NORTH) on the top side of the socket and NM-AMB12b (SOUTH) on the bottom, using the -7mm offset holes, and fix both with the 4 NM-ALS1 long screws.
Watch out: Both CPU arrows must point toward the CPU, with NORTH on top. Tighten gently until the screws stop, never more than 0.6 Nm.
Tip: Use the standard 0 holes only if the -7mm offset position hits a motherboard heatsink.
-
Step 4: Apply the thermal paste
Clean any old thermal paste or pads off the CPU first. Then put 5 dots of NT-H1 on it: 4 small dots of about 2 mm near the corners and 1 dot of 3 to 4 mm in the centre.
Watch out: Too much thermal paste lowers heat conductivity and cooling performance. Keep the dots to the sizes shown.
-
Step 5: Fasten the heatsink to the CPU
Unclip the centre fan and set it aside, then take the protection cover off the heatsink base. Set the heatsink on the CPU and give each of its two screws 2 to 3 turns, switching between them until both are tight.
Watch out: Take the protection cover off the base before it meets the paste. Tighten gently until the screws stop, never more than 0.6 Nm.
Tip: Reach the two screws through the gap where the centre fan sat.
-
Step 6: Refit the centre fan and add the second
Clip the centre fan back between the two fin stacks. For more cooling, fit the second fan to the outer face of the front fin stack with the two supplied steel clips.
Watch out: With tall RAM modules, use the centre fan only. The second fan may not clear them.
Tip: The centre fan goes back on with the clips it came off with. The simplest reading of the drawing is that the two loose steel clips are for the second fan.
-
Step 7: Connect the fans
Plug the fans into the motherboard's CPU fan header or headers. To run both fans from one header, join them with the NA-YC1 splitter cable. You can add the NA-RC7 Low-Noise Adaptors, one per fan, to make them quieter.
Watch out: Never use one Low-Noise Adaptor for both fans by putting it before the splitter cable.
-
Step 8: Check clearance and CPU temperature
Check that the heatsink and fan clips do not touch the graphics card, other PCIe cards or motherboard heatsinks. If you use the Low-Noise Adaptors, watch the CPU temperature in your motherboard maker's software.
Watch out: Take the cooler off before you ship or transport the PC. Transport forces cannot be controlled and can cause damage with the heatsink installed.
Tip: If cooling falls short with the adaptors, add case ventilation or remove the adaptors.
