Tools

None: a large ceramic mug, a full bottle of descaling solution and a sink.

Parts (6)

PartCountSizeGoes inNote
Brewer133 × 24 × 18 cmstep 2The main body with the handle, the K-Cup pod holder and the buttons on top. It stays upright the whole time.
Drip tray115 × 9 × 2 cmstep 2The perforated tray at the front of the brewer. The mug sits on it; leave it in place.
Water reservoir130 × 22 × 7 cmstep 5The tall clear tank on the left side with the MAX fill line. Its lock tab clicks into the brewer.
Water reservoir lid122.4 × 7.4 × 2 cmstep 5The small dark cap on top of the reservoir. Lift it off before you pour anything in.
Large ceramic mug1Ø 9 × 11 cmstep 6A large ceramic mug, not a paper cup. It catches every rinsing brew.
Keurig Descaling Solution bottle1Ø 7 × 20 cmstep 5The full bottle of Keurig Descaling Solution. Taller and narrower than the mug; all of it goes in.

The 13 steps

  1. Step 1: Gather what you need

    2 min

    You need a large ceramic mug, fresh water, a full bottle of Keurig Descaling Solution and access to a sink. Allow about 45 minutes for the whole procedure.

    Tip: Do not use a paper cup. Descale every 3 to 6 months, more often if scale builds up fast in your water.

  2. Step 2: Set up by the sink and check the pod holder

    1 min

    Put the brewer on the counter near a sink. Lift the handle, make sure there is no pod in the K-Cup pod holder, then lower the handle all the way.

    Watch out: Keep your fingers out of the pod holder. There are sharp needles above it and in its bottom.

  3. Step 3: Empty the water reservoir

    1 min

    Take the lid off the water reservoir and lift the reservoir straight up out of the brewer. Pour the water into the sink. If you use a Keurig Water Filter, take it out and set it aside.

    Tip: The reservoir is the clear tank on the left side of the brewer as you face it.

  4. Step 4: Turn the brewer off

    1 min

    Press the power button to turn the brewer off before you add the solution.

  5. Step 5: Pour in the descaling solution

    2 min

    Pour the whole bottle of Keurig Descaling Solution into the empty reservoir. Fill the empty bottle with water and pour that in too. Set the reservoir back with the lock tab engaged, put the lid on, then press the power button to turn the brewer on.

    Watch out: Press the reservoir down until the lock tab engages. A reservoir that is not seated in its base can keep the ADD WATER light on.

  6. Step 6: Place the mug and run a rinsing brew

    2 min

    Place the large ceramic mug on the drip tray. Press the HOT WATER button, then the largest brew size, the 12oz Travel Mug button.

    Watch out: Do not lift the handle while it brews. There is extremely hot water in the K-Cup pod holder.

  7. Step 7: Repeat until the ADD WATER light comes on

    3 min

    Pour the mug into the sink, put it back on the drip tray and run another rinsing brew the same way. Keep going until the ADD WATER light comes on.

    Watch out: Do not use a K-Cup pod for any of these brews.

    Tip: Foam from the brewer is normal. The solution is reacting with the scale inside.

  8. Step 8: Let it stand for 30 minutes

    15 min

    Leave the brewer switched on and let it stand for at least 30 minutes with the solution inside.

    Watch out: Do not turn it off or empty it early. The manual asks for at least 30 minutes with the brewer still on.

  9. Step 9: Empty and rinse the reservoir

    2 min

    After 30 minutes, lift the reservoir out, pour any leftover solution into the sink and rinse the reservoir thoroughly with fresh water.

    Tip: Do not dry the inside with a cloth, lint can stay behind. The reservoir does not go in the dishwasher.

  10. Step 10: Fill with fresh water to MAX

    1 min

    Fill the reservoir with fresh water to the MAX fill line. Set it back so the lock tab engages and put the lid on.

    Watch out: Stop at the MAX fill line. Do not fill beyond it.

  11. Step 11: Run a fresh water rinse

    2 min

    Place the large mug on the drip tray and run a rinsing brew: press HOT WATER, then the largest brew size. Pour the mug into the sink.

    Watch out: No K-Cup pod. Keep the handle down while it brews; the pod holder is full of very hot water.

  12. Step 12: Rinse until you reach 12 brews

    11 min

    Repeat the rinsing brew, pouring the mug into the sink each time, until you have run at least 12 rinsing brews at the largest size. Refill the reservoir with fresh water to MAX when it runs low.

    Watch out: Stopping before 12 rinses can leave descaling solution in the brewer.

    Tip: You will need to refill the reservoir at least once. Make a tally mark after each brew so you keep count.

  13. Step 13: If only a trickle comes out

    2 min

    A heavily scaled brewer may give little or no water and blow air after the descaler. If so, turn it off and unplug it, empty and rinse the reservoir, refill with water, plug it back in, power on and repeat the fresh water rinse.

    Watch out: Turn the brewer off and unplug it before you empty the reservoir.

    Tip: If it keeps happening, leave the brewer unplugged for at least 30 minutes before you continue the rinse.