Tools
None: one descaling powder sachet and a 1 L jug of water.
Parts (5)
| Part | Count | Size | Goes in | Note |
|---|---|---|---|---|
| Espresso machine | 1 | 38 × 32 × 22 cm | step 2 | The whole machine with the control panel on the front. The water tank clips into its back. |
| Water tank, 2 L | 1 | 28 × 22 × 8 cm | step 3 | Clear 2 L tank with a lift handle on top. It sits at the back of the machine. |
| Drip tray | 1 | 30 × 10 × 5 cm | step 2 | Wide steel tray at the front foot, with the Empty Me! indicator in it. |
| Steam wand | 1 | Ø 1 × 14 cm | step 2 | Thin steel tube at the right front. Steam and descaler come out of its tip. |
| Steam / hot water dial | 1 | Ø 4 × 2 cm | step 2 | Round knob on the right side of the machine, with steam, standby and hot water positions. |
The 10 steps
-
Step 1: Get ready to descale
Clear space around the machine on a level, dry counter. Have one Breville descaling powder sachet and a 1 L jug of water ready.
Tip: Descaling takes about 20 minutes. Stay with the machine, because it turns itself off after 5 idle minutes in descale mode.
-
Step 2: Check the CLEAN / DESCALE light
Look at the CLEAN / DESCALE light on the control panel. When it is lit solid, the machine needs descaling. Make sure the drip tray is pushed fully in before you start.
Watch out: Do not immerse the power cord, plug or machine in water or any other liquid. Never remove or fully empty the water tank while descaling.
Tip: A flashing CLEAN / DESCALE light means a cleaning cycle (backflush) is due instead. That is a separate job on page 24.
-
Step 3: Mix the descaler and fill the tank
Dissolve one Breville descaling powder sachet in 1 L (34 fl oz) of water. Lift the tank out by its handle at the back, pour in the solution, then lower it back and push down until it locks.
Watch out: If the tank is not pushed all the way down and locked, no water flows. Press it down firmly until it seats.
-
Step 4: Enter descale mode
Press and hold the 2 CUP button, then press and hold POWER at the same time. POWER flashes while the machine heats. It is ready when POWER, 1 CUP, CLEAN / DESCALE and the steam/hot water light all stay on.
Tip: If you do nothing for 5 minutes in descale mode, the machine turns itself off. Start again from this step.
-
Step 5: Descale the coffee side
Press the 1 CUP button. The solution runs through the group head for about 25 seconds while 1 CUP flashes, and the button stays lit when it is finished. Press 1 CUP again if you need to stop early.
Tip: The solution drains into the drip tray. Empty the tray whenever the Empty Me! indicator shows, then push it firmly back in.
-
Step 6: Descale the steam wand
Point the steam wand tip over the drip tray. Turn the steam dial toward the steam icon and let it run for about 13 seconds. Turn the dial back to STANDBY to stop early.
Watch out: Do not touch hot surfaces. The steam wand gets hot, so touch only the dial.
Tip: The manual says to turn the dial right here, but its dial drawings put steam on the left. Go by the steam icon printed next to the dial.
-
Step 7: Descale the hot water outlet
Turn the steam dial the other way, toward the hot water icon, and let it run for about 8 seconds. Then return the dial to STANDBY.
Tip: Go by the water-drop icon next to the dial. The manual's text says left, the opposite of the steam direction.
-
Step 8: Repeat to use up the solution
About half the solution (0.5 L, 17 fl oz) is left in the tank. Run the same three again: press 1 CUP for the coffee side, turn the dial to steam, then to hot water, then back to STANDBY. Keep going until the solution is used up.
Watch out: Do not lift the tank out during these runs. It stays locked in place until the rinse in the next step.
-
Step 9: Rinse the tank and flush with fresh water
Lift the tank out and rinse it well. Fill it with fresh cold water to MAX (2 L, 68 fl oz) and lock it back in. Run 1 CUP, steam and hot water again to flush any descaler out of the machine.
Tip: Empty the drip tray before the flush, because it now holds used descaling solution.
-
Step 10: Quit descale mode
Press POWER to leave descale mode. The lights switch off when it is done.
Watch out: Do not touch hot surfaces. Let the machine cool down before you move it or clean any parts.
