Tools
- Flat screwdriver, steps 5, 8, 13 and 20
- Phillips screwdriver, steps 2, 6, 10, 18 and 25
- Hammer, steps 3, 16 and 23
- Scissors
- Hex key 100001 (in the bag), step 24
Parts (30)
| Part | Count | Size | Goes in | Note |
|---|---|---|---|---|
| Side panel, left | 1 | 66 × 58 × 1.5 cm | step 4 | Big panel with five drawer runners on one face; the right side is its mirror. |
| Side panel, right | 1 | 66 × 58 × 1.5 cm | step 4 | Big panel with five drawer runners; mirror of the left side. |
| Back panel | 1 | 66 × 33 × 1.5 cm | step 4 | The long, narrow panel with six round cam holes along its long edges. |
| Bottom panel | 1 | 58 × 36 × 1.5 cm | step 7 | Same size as the top; small glide holes near the corners. Check it against manual step 6. |
| Top panel | 1 | 58 × 36 × 1.5 cm | step 7 | Same size as the bottom panel; turn it as manual step 6 shows for your setup. |
| Drawer front, shallow (top slot) | 1 | 32.6 × 10.5 × 1.5 cm | step 18 | The lower of the two front sizes, curved finger pull on top. |
| Drawer front, shallow (second slot) | 1 | 32.6 × 10.5 × 1.5 cm | step 18 | The lower of the two front sizes, curved finger pull on top. |
| Drawer front, tall (middle slot) | 1 | 32.6 × 14.4 × 1.5 cm | step 10 | The taller of the two front sizes, curved finger pull on top. |
| Drawer front, tall (fourth slot) | 1 | 32.6 × 14.4 × 1.5 cm | step 10 | The taller of the two front sizes, curved finger pull on top. |
| Drawer front, tall (bottom slot) | 1 | 32.6 × 14.4 × 1.5 cm | step 10 | The taller of the two front sizes, curved finger pull on top. |
| Shallow drawer side | 4 | 51.5 × 8 × 1.2 cm | step 19 | The lower drawer side: one dowel hole and one cam hole at the front end. |
| Tall drawer side | 6 | 51.5 × 12 × 1.2 cm | steps 11 and 12 | The taller drawer side: two cam holes near the front end. |
| Drawer bottom | 5 | 50 × 28.7 cm, 3 mm thick | steps 14 and 21 | Thin board; all five drawer bottoms are the same. |
| Drawer back, shallow | 2 | 28.7 × 6.5 × 1.2 cm | step 22 | The lower of the two drawer back sizes. |
| Drawer back, tall | 3 | 28.7 × 10.5 × 1.2 cm | step 15 | The taller of the two drawer back sizes. |
Hardware (122 pieces)
| Part no. | Hardware | Count | Size | Used in |
|---|---|---|---|---|
| 118331 | Cam bolt | ×34 | Ø 7 × 36 mm | steps 2, 6, 10 and 18 |
| 101345 | Wooden dowel | ×16 | Ø 8 × 34 mm | steps 3 and 17 |
| 119251 | Cam lock, slotted (carcass) | ×18 | Ø 15 × 13 mm | steps 5 and 8 |
| 103114 | Cam lock, cross head (drawers) | ×16 | Ø 12 × 10 mm | steps 13 and 20 |
| 10061614 | Glide | ×4 | Ø 25 × 10 mm | step 9 |
| 110519 | Plastic pin with round head | ×20 | Ø 8 × 42 mm | steps 16 and 23 |
| 110907 | Hex socket screw (desk top only) | ×4 | Ø 6 × 34 mm | step 24 |
| 105021 | Short screw | ×10 | Ø 4 × 12 mm | step 25 |
Sizes are as drawn in the 3D: diameter × length for fasteners, in millimeters.
The 25 steps
-
Step 1: Check your parts
Lay everything on a rug or the flattened box. Count the five carcass panels and the parts for five drawers, then tip each hardware bag into its own bowl.
Tip: Keep hex key 100001 to hand. The 4 screws 110907 are only for a desk top, and casters are sold separately with their own manual.
-
Step 2: Screw cam bolts into both sides
Lay both side panels flat on the rug, runners up. Screw 3 cam bolts 118331 into the holes along the back edge of each side, 6 in total.
Watch out: Stop when the collar sits on the panel. A bolt that goes in deeper or crooked won't catch its cam lock later.
-
Step 3: Push in 12 wooden dowels
Push wooden dowels 101345 into the small edge holes of both sides and the long, narrow back panel, 4 per panel and 12 in total. Tap them home lightly with the hammer.
Tip: The manual's step 2 drawing shows exactly which holes. Dowels go in the edges, never the faces.
-
Step 4: Stand the sides on the back panel
Lay the back panel flat, cam holes up: the unit is built lying on its back. Stand both sides on its long edges, runners facing in, and press them onto the dowels and cam bolts.
Watch out: The runners must face inward and run toward the open front. If one faces out, you have swapped the sides.
Tip: Ask someone to hold the first side upright while you fit the second.
-
Step 5: Lock the back with 6 cam locks
Drop 6 cam locks 119251 into the round holes in the back panel, 3 along each side. Turn each one half a turn with the flat screwdriver until the side pulls tight.
Watch out: Use the slotted cam locks 119251 here, not the cross-head 103114. The manual crosses those out; they are for the drawers.
-
Step 6: Screw cam bolts into top and bottom
Lay the top and bottom panels flat. Screw 6 cam bolts 118331 into each, 3 along each long edge, 12 in total.
Tip: Collar flush with the board, the same as the bolts in the sides.
-
Step 7: Fit the top and bottom panels
With the unit still on its back, push the bottom panel onto one end of the sides and the top panel onto the other, bolts into the big holes and dowels into the small ones.
Watch out: Top and bottom have different small holes. Match them to the manual's step 6 drawing for your setup: free-standing or under a desk top.
-
Step 8: Lock top and bottom with 12 cams
Push 12 cam locks 119251 into the holes near both ends of each side, 3 per end. Turn each half a turn with the flat screwdriver until the panels pull tight.
Watch out: Turn each cam's open side toward its bolt before you push it in, or it won't catch. Slotted 119251 again, not 103114.
-
Step 9: Press on the glides, then stand it up
Skip this if you fit casters (sold separately). Peel the film off each glide 10061614 and press it into the 4 corner holes of the bottom panel. Then tip the unit upright.
Tip: The manual's last page shows another way: cut a 20 x 20 mm square, press it on at each corner and the glide on top. It doesn't name the material, so follow that drawing.
-
Step 10: Bolt the three tall drawer fronts
Lay a tall drawer front face down, groove up. Screw 4 cam bolts 118331 into its inner face, 2 near each end. Repeat for the other two tall fronts: 12 bolts.
Tip: The 3D view builds each drawer in its slot so you see where it goes. You build it on the rug, face down. The two shallow drawers come later.
-
Step 11: Fit sides to two tall fronts
Push a tall drawer side onto the bolts at each end of a tall front, grooves facing in toward each other. Do this for two of the three tall fronts.
Watch out: If a groove faces out, the bottom board has nowhere to go. Swap the sides before the cams go in.
-
Step 12: Fit sides to the third tall front
Push the last two tall sides onto the bolts of the third tall front, grooves facing in.
-
Step 13: Lock the tall drawer sides
Push a cross-head cam lock 103114 into each round hole on the outside of the tall drawer sides, 4 per drawer and 12 in total. Turn each half a turn until the side pulls tight to the front.
Watch out: These are the smaller cross-head 103114 cams, not the slotted 119251 ones.
-
Step 14: Slide in the tall drawer bottoms
Slide a thin bottom board into the grooves of both sides from the open end until it sits in the front's groove. Do this for all three tall drawers.
Tip: Check it runs in the groove on both sides along its whole length before the back goes on.
-
Step 15: Drop in the tall drawer backs
Lower each tall back into the notches at the open end of its sides, over the bottom board, until it sits flush with the ends of the sides.
-
Step 16: Hammer the pins into the tall drawers
Hammer 2 plastic pins 110519 through each side into the back, 4 per drawer and 12 in total, until the round heads sit flat. Then turn each drawer upright.
Watch out: These pins don't come out cleanly. Check the bottom sits in its grooves and the back is flush before you hammer.
-
Step 17: Push dowels into the shallow sides
Take the 4 shallow drawer sides and push a wooden dowel 101345 into the small hole at the front end of each.
Tip: The shallow drawers join with 1 dowel and 1 cam per side instead of 2 cams.
-
Step 18: Bolt the two shallow fronts
Lay each shallow front face down, groove up, and screw 2 cam bolts 118331 into its inner face, one near each end. 4 bolts in total.
-
Step 19: Fit the sides to the shallow fronts
Push two shallow sides onto each shallow front, the dowel and the bolt into their holes, grooves facing in.
Watch out: If a groove faces out, swap the sides before the cams go in.
-
Step 20: Lock the shallow drawer sides
Push a cam lock 103114 into the round hole on the outside of each shallow side, 4 in total, and turn it half a turn until it locks.
Tip: The manual prints 4x here: that is both shallow drawers, 2 cams each.
-
Step 21: Slide in the shallow drawer bottoms
Slide a bottom board into the grooves of each shallow drawer from the open end until it sits in the front's groove.
-
Step 22: Drop in the shallow drawer backs
Lower each shallow back into the notches at the open end of its sides, over the bottom board, flush with the side ends.
-
Step 23: Hammer the pins into the shallow drawers
Hammer 2 plastic pins 110519 through each side into the back, 4 per drawer and 8 in total, then turn the drawers upright.
Watch out: The pins don't come out cleanly. Check the bottom and the back are seated before you hammer.
-
Step 24: Screw on a desk top (desk use only)
Skip this unless the unit goes under a desk top (sold separately: LAGKAPTEN, MÅLSKYTT or ANFALLARE). Turn the desk top onto the legs and this unit, then drive 4 screws 110907 up through the top panel with hex key 100001.
Watch out: Line the small pre-drilled marks under the desk top up with the holes in the ALEX top before you drive a screw.
Tip: You reach the screws from inside the empty unit. The drawers go in only in the next step, even though the 3D view shows them.
-
Step 25: Fit the drawers and stop screws
The 2 shallow drawers go in the top two slots, the 3 tall ones below. Hook each onto its runners, push it in, pull it out again and drive 2 short screws 105021 into the runner holes. 10 in total.
Watch out: Never stack one ALEX on top of another. The manual warns against it: the stack can tip over.
